|
|
|
|
|
Ruilin Liu, Yunqi Liu, Hongming Liu, Yuanxing Li, Hui Chen and Zongtao Zhu
Laser?MIG hybrid welding?brazing was used to weld 304 stainless steel and 6061-T6 aluminum alloy with a thickness of 2 mm. The microstructure, morphology, chemical composition and corrosion behavior of the samples after high-temperature oxidation were in...
ver más
|
|
|
|
|
|
|
|
|
|
|
Marvin Montoya, Juan Genesca and Rodrigo Montoya
The galvanic corrosion behavior of the AA7075?CS1018 couple was examined in dynamic electrolytes using the ZRA technique. A modified electrochemical setup was developed to support the use of thin-film gel and liquid electrolytes on metallic surfaces. Thi...
ver más
|
|
|
|
|
|
|
|
|
|
|
Luciano Macera, Daniele Pullini, Alberto Boschetto, Luana Bottini, Claudio Mingazzini and Gian Luca Falleti
Metal additive manufacturing is a rapidly growing field based on the fabrication of complex parts with improved performance. The advantages of using this technology include the production of shapes that cannot be produced by traditional machining technol...
ver más
|
|
|
|
|
|
|
|
|
|
|
Jaehui Bang and Eunkyung Lee
In this study, the surface properties of marine structures were improved by applying a twin wire arc spray process to high-strength low alloys. The effect of Al and Mo contents in Ni-Al coatings on their mechanical and corrosion behaviors was analyzed us...
ver más
|
|
|
|
|
|
|
|
|
|
|
Alan Rondineau, Laurent Gaillet, Lamine Dieng and Sébastien Langlois
High-voltage electrical cables are prone to saline corrosion, mostly in coastal environments. Steel wires are a crucial element in withstanding the mechanical solicitations of commonly used aluminum conductor steel reinforced (ACSR) cables. An experiment...
ver más
|
|
|
|
|
|
|
|
|
|
|
Andreas Gericke, Michél Hauer, Benjamin Ripsch, Michael Irmer, Jonas Nehlsen and Knuth-Michael Henkel
The influence of thermally sprayed aluminum coatings (Al99%; arc spraying) on the fatigue strength of gas metal arc welded (GMAW) non-alloyed structural steel specimens with respect to foundations for offshore wind turbines was investigated. Additionally...
ver más
|
|
|
|
|
|
|
|
|
|
|
Goutham Issac Ashok Kumar, Alexander Lambert, Joshua Caperton, Muthappan Asokan, William Yi and Oliver Chyan
The introduction of copper as wire bonding material brings about a new challenge of aluminum bond pad bimetallic corrosion at the copper/aluminum galvanic interface. Aluminum is well known to undergo pitting corrosion under halide-contaminated environmen...
ver más
|
|
|
|
|
|
|
|
|
|
|
Seonghwan Park, Cheolmin Ahn and Eunkyung Lee
High-pressure die-cast AlSi10MnMg (AA365) alloys have been used as a material for automotive components exposed to high temperature and corrosive environments. This work determines the correlation of corrosion resistance with the intermetallic compounds ...
ver más
|
|
|
|
|
|
|
|
|
|
|
Taeyong Kim, Youn-Jung Lee, Simpy Sanyal, Jung-Wook Woo, In-Hyuk Choi and Junsin Yi
Porcelain insulators should be exchanged periodically, but their lifetime is not clearly defined. One factor that affects service life is corrosion occurring at the pin and cap?each of which is made of iron with a zinc coating. A number of porcelain insu...
ver más
|
|
|
|
|
|
|
|
|
|
|
Bronach Healy, Tian Yu, Daniele da Silva Alves and Carmel B. Breslin
Corrosion is a naturally occurring phenomenon and there is continuous interest in the development of new and more protective coatings or films that can be employed to prevent or minimise corrosion. In this review the corrosion protection afforded by two-...
ver más
|
|
|
|
|
|