|
|
|
Kirttayoth Yeranee, Yu Rao, Chao Xu, Yueliang Zhang and Xiyuan Su
Additive manufacturing allows the fabrication of relatively complex cooling structures, such as triply periodic minimal surface (TPMS), which offers high heat transfer per unit volume. This study shows the turbulent flow heat transfer and thermal stress ...
ver más
|
|
|
|
|
|
|
Sanjay Nambiar, Anan Ashrabi Ananno, Herman Titus, Anton Wiberg and Mehdi Tarkian
In the quest to enhance the efficiency of gas turbines, there is a growing demand for innovative solutions to optimize high-pressure turbine blade cooling. However, the traditional methods for achieving this optimization are known for their complexity an...
ver más
|
|
|
|
|
|
|
Wang Xiao, Yifan Chen, Huisheng Zhang and Denghai Shen
Turbine blades are crucial components exposed to harsh conditions, such as high temperatures, high pressures, and high rotational speeds. It is of great significance to accurately predict the life of blades for reducing maintenance cost and improving the...
ver más
|
|
|
|
|
|
|
Hongxin Zhu, Yimin Zhu, Xiaoyi Zhang, Jian Chen, Mingyu Luo and Weiguang Huang
Performing online damage evaluation of blades subjected to complex cyclic loads based on the operating state of a gas turbine enables real-time reflection of a blade?s damage condition. This, in turn, facilitates the achievement of predictive maintenance...
ver más
|
|
|
|
|
|
|
Artur Kulaszka, Józef Blachnio and Henryk Borowczyk
The reliability and operational safety of an aircraft engine gas turbine are extremely important in terms of its operation. In the course of operation, these turbines undergo complex thermal, mechanical, aerodynamic, and chemical exhaust gas loads. Due t...
ver más
|
|
|
|
|
|
|
Hamed Abdeh, Giovanna Barigozzi and Nicoletta Franchina
Off-design condition of a rotor blade cascade with and without platform cooling was experimentally investigated. The ability of the gas turbine to operate down to 50% to 20% of its nominal intake air flow rate has an important consequence in the change i...
ver más
|
|
|
|
|
|
|
Filippo Merli, Nicolas Krajnc, Asim Hafizovic, Marios Patinios and Emil Göttlich
The purpose of the paper is to characterize the aerodynamic behavior of a rotor-downstream hub cavity rim seal in a high-pressure turbine (HPT) stage. The experimental data are acquired in the Transonic Test Turbine Facility at the Graz University of Tec...
ver más
|
|
|
|
|
|
|
Jörg R. Riccius and Evgeny B. Zametaev
A numerical turbine-blade fatigue-life analysis method is suggested. This method comprises a stationary thermal 3D finite element (FE) analysis of the hot run for the combined high-cycle fatigue (HCF) and creep analysis, and a follow-on (one-way coupled)...
ver más
|
|
|
|
|
|
|
Anitha Kumari Azmeera, Prakash Jadhav and Chhaya Lande
Upgrading abradable or wearable coatings in the high-temperature zone of aero engines is advised to increase the efficiency and high-density power in gas turbine engines for military or commercial fixed-wing and rotary-wing aircraft. The development of t...
ver más
|
|
|
|
|
|
|
Dongjie Yan, Hongmei Jiang, Jieling Li, Wenbo Xie, Zhaoguang Wang, Shaopeng Lu and Qiang Zhang
In high-pressure turbines, there is a large difference in temperature between the mainstream and the turbine blade surface. Most of the turbine blade tip heat transfer studies were conducted under the assumption that the Over-Tip-Leakage (OTL) flow field...
ver más
|
|
|
|