|
|
|
|
|
K.N. Likitha , Kundhena Srinivas, S.C. Gurudev, G.D. Nischith , C. Rajasekaran
|
|
|
|
|
|
|
|
|
|
|
Abdul Basit, Safeer Abbas, Muhammad Mubashir Ajmal, Ubaid Ahmad Mughal, Syed Minhaj Saleem Kazmi and Muhammad Junaid Munir
This study undertakes a comprehensive experimental and numerical analysis of the structural integrity of buried RC sewerage pipes, focusing on the performance of two distinct jointing materials: cement mortar and non-shrinkage grout. Through joint shear ...
ver más
|
|
|
|
|
|
|
|
|
|
|
Xiaoqing Cao, Lu Li, Fengwei Zhang, Fangyuan Zhang, Xuefeng Song, Wuyun Zhao and Fei Dai
Livestock dung, discarded crop straws, and residual plastic film are the primary agricultural non-point sources of pollution. For livestock dung and discarded crop straw, the general treatment focuses on compost, animal fodder, industrial raw material, a...
ver más
|
|
|
|
|
|
|
|
|
|
|
Truong-Linh Chau, Thu-Ha Nguyen and Van-Ngoc Pham
Mechanically stabilized earth (MSE) walls have been widely applied in construction to maintain the stability of high embankments. In Vietnam, imported reinforcement materials are expensive; thus, finding locally available materials for MSE walls is benef...
ver más
|
|
|
|
|
|
|
|
|
|
|
Kyong Min Ro, Min Sook Kim and Young Hak Lee
The previous research introduced an innovative retrofitting technique for reinforced concrete beams using modularized steel plates. This technique enhances structural performance, offering a lightweight solution compared to conventional retrofitting meth...
ver más
|
|
|
|
|
|
|
|
|
|
|
Jiaqi Hu, Yin Gu, Jinhuang Yan, Ying Sun and Xinyi Huang
With the convenient and fast requirements for construction in bridge engineering, prefabricated assembly technology is widely applied in engineering construction. Typically, prefabricated bridge decks are connected through cast-in-place wet joints. Wet j...
ver más
|
|
|
|
|
|
|
|
|
|
|
Xuewen Fu, Ximei Wei, Meng Wang, Hongwen Zhang, Lei Wang, Jun Wang and Yuanzhao Zheng
This study investigated the impact of compression molding parameters on the post-molding characteristics of machine-harvested seed cotton and aimed to determine the optimal compression molding parameters. The closed compression test of seed cotton and fo...
ver más
|
|
|
|
|
|
|
|
|
|
|
Yashi Yang, Peng Zhang, Lingjun Wu and Qian Zhang
High-pile foundation is a common form of deep foundation commonly used in ocean environments, such as docks and bridge sites. Aiming at the problem of bearing capacity of high pile foundations, this paper proposes the calculation of bearing capacity and ...
ver más
|
|
|
|
|
|
|
|
|
|
|
Miao Li, Hao Li and Yang Wen
A new type of spherical node was used to design a laboratory-scale prototype of a six-leg lattice of steel tubes and concrete for application as a wind turbine tower. Repeated load tests were performed on the prototype tower for several weeks to evaluate...
ver más
|
|
|
|
|
|
|
|
|
|
|
Deli Jiang, Xuegeng Chen, Limin Yan, Jinhao Zhang, Tao Wu and Xuanhe Fu
Compared with the conventional horizontal conveyor-chain-type plastic-film-picking device, the longitudinal nail-tooth-chain-plate-type plastic-film-picking device developed by our team in the early stage has little tearing effect on the mulching film, a...
ver más
|
|
|
|
|
|