|
|
|
|
|
Bora Pulatsu, Rhea Wilson, Jose V. Lemos and Neboj?a Mojsilovic
Unreinforced masonry (URM) walls are common load-bearing structural elements in most existing buildings, consisting of masonry units (bricks) and mortar joints. They indicate a highly nonlinear and complex behaviour when subjected to combined compression...
ver más
|
|
|
|
|
|
|
|
|
|
|
Mridupol Handique, Popy Bora, Vasileios Ziogas, Anoop Kumar Srivastava, Prasanth Tej Kumar Jagannadham and Asish Kumar Das
Phytophthora gummosis, foot rot, and root rot are considered major challenges to the citrus industry worldwide. Little is known about the Phytophthora?microbiome interaction, despite several studies demonstrating changes in the microbial composition of t...
ver más
|
|
|
|
|
|
|
|
|
|
|
Sumira Malik, Shristi Kishore, Archna Dhasmana, Preeti Kumari, Tamoghni Mitra, Vishal Chaudhary, Ritu Kumari, Jutishna Bora, Anuj Ranjan, Tatiana Minkina and Vishnu D. Rajput
The treatment of wastewater is an expensive and energy-extensive practice that not only ensures the power generation requirements to sustain the current energy demands of an increasing human population but also aids in the subsequent removal of enormous ...
ver más
|
|
|
|
|
|
|
|
|
|
|
Yunji Kim, Junho Suh, Bora Lee, Yondo Chun, Keejun Park and Yonghun Yu
This study analyzed adhesive wear in periodic sliding motion using a quasi-static deterministic wear model that considered changes in the point of contact of asperities as well as changes in the surface and statistical parameters. The contact pressure wa...
ver más
|
|
|
|
|
|
|
|
|
|
|
Bora GUNDUZYELI
Pág. 001 - 017
|
|
|
|
|
|
|
|
|
|
|
Ali Zaib, Jingbo Yin and Rafi Ullah Khan
Safety has been a primary concern in every industry. It includes system, personnel, environmental safety, etc. Maritime transportation safety is of the utmost importance because a lot of economic and environmental damage has been caused by ship-related a...
ver más
|
|
|
|
|
|
|
|
|
|
|
Bhabani Bora, Ratnesh Kumar, Somnath Chattopadhyaya and Sebastian Borucki
In this investigation, dissimilar material AA6061-T6 and Cu B370 were joined by friction stir welding (FSW). This paper presents a feasibility study of FSW to join Al-alloy and Cu-alloy. The experiment was conducted using general full factorial design by...
ver más
|
|
|
|
|
|
|
|
|
|
|
Bora Pulatsu, Semih Gonen and Paulo B. Lourenço
Unreinforced masonry structures are susceptible to man-made hazards such as impact and blast loading. However, the literature on this subject mainly focuses on masonry wall behavior, and there is a knowledge gap about the behavior of masonry arches under...
ver más
|
|
|
|
|
|
|
|
|
|
|
Saeed Hariri
This paper describes the near-surface transport properties and Lagrangian statistics in the Adriatic semi-enclosed basin using synthetic drifters. Lagrangian transport models were used to simulate synthetic trajectories from the mean flow fields obtained...
ver más
|
|
|
|
|
|
|
|
|
|
|
Rahmetullah Varol, Gokhan Bora Esmer and Huseyin Uvet
A three-dimensional profile reconstruction of live cells in dynamic cell cultures is a challenging problem due to the highly scattering nature of cell mediums. Furthermore, it is an interesting problem since these cultures present the optimal in vitro co...
ver más
|
|
|
|
|
|