|
|
|
|
|
Hua Huang, Zhenfeng Peng, Jinkun Hou, Xudong Zheng, Yuxi Ding and Han Wu
Disc buckle steel pipe brackets are widely used in building construction due to the advantages of its simple structure, large-bearing capacity, rapid assembling and disassembling, and strong versatility. In complex construction projects, the uncertaintie...
ver más
|
|
|
|
|
|
|
|
|
|
|
Xianquan Wang, Yong Qiu, Jie Yuan, Dongyan Liu, Peiyu Shi, Chenchen Zhao, Shanyuan Xu and Tengfei Zhao
Spatial truss structures (STSs), serving as the bottom support structure of a cooling tower, effectively harness the superior load-bearing capacity offered by lattice-type truss structures. STSs are composed of main bars, diagonal bars, and horizontal ba...
ver más
|
|
|
|
|
|
|
|
|
|
|
Manuel Moya, David Sánchez, José Ángel Romero and José Ramón Villar-García
The loads generated inside agricultural silos under static and dynamic conditions depend on the mechanical properties of the materials stored inside them. Silo calculation methodologies are based on these mechanical properties. Although it is known that ...
ver más
|
|
|
|
|
|
|
|
|
|
|
Qi Yan, Zhiqiang Wan and Chao Yang
Flight load calculation, an important step in aircraft design and optimization, typically involves millions of computations and requires significant computing resources and time. Improving the efficiency of flight load calculations while maintaining accu...
ver más
|
|
|
|
|
|
|
|
|
|
|
Guo Li, Shuchun Huang, Wanqiu Lu, Junbo Liu, Shuiting Ding, Gong Zhang and Bo Zhen
Probabilistic failure risk analysis of aeroengine life-limited parts is of great significance for flight safety. Current probabilistic failure risk analysis uses equal amplitude load calculations for conservative estimation, avoiding inclusion of the int...
ver más
|
|
|
|
|
|
|
|
|
|
|
Mengchuang Zhang, Shasha Xia, Yongsheng Huang, Jiawei Tian and Zhiping Yin
Flight maneuver recognition (FMR) is a critical tool for capturing essential information about the state of an aircraft, which is necessary to improve pilot training, flight safety, and autonomous air combat. However, due to the alignment of multidimensi...
ver más
|
|
|
|
|
|
|
|
|
|
|
Yuantian Qin, Yucheng Zhang, Vadim Silberschmidt and Luping Zhang
The location identification of dynamic load is an important part of load-identification technology. Traditional methods are mostly aimed at the identification of dynamic load?s amplitude and phase. A new method for dynamic load location identification is...
ver más
|
|
|
|
|
|
|
|
|
|
|
Michael Frenzel, Enrico Baumgärtel, Steffen Marx and Manfred Curbach
This article presents the cracking and load-bearing behaviour of carbon-reinforced prismatic concrete tensile specimens. Grids with different geometries and impregnations were used as carbon reinforcement. In addition, the roving surfaces were partially ...
ver más
|
|
|
|
|
|
|
|
|
|
|
Sung-Eun Cho
The maintenance of water-retaining structures involves evaluating their performance against current and future operating water levels. Fragility curves are commonly used for this purpose, as they indicate the conditional probability of failure for variou...
ver más
|
|
|
|
|
|
|
|
|
|
|
Stian H. Sørum, Nuno Fonseca, Michael Kent and Rui Pedro Faria
Fibre ropes offer beneficial properties for mooring of floating offshore wind turbines (FOWTs). However, the mooring line?s stiffness is both load-history and load-rate dependent. A quasi-static stiffness is observed for slow loading, with a higher stiff...
ver más
|
|
|
|
|
|