|
|
|
|
|
Yiyao Jiang, Guang Feng, Panglun Liu, Li Yuan, Jianbin Ding and Bingyan Jiang
Through the establishment of a three-dimensional joint clearance model, the effects of joint clearances at different positions on shimmy stability are evaluated. In this paper, considering the radial, axial and coupling characteristics of joint clearance...
ver más
|
|
|
|
|
|
|
|
|
|
|
Zhangping You, Haiyang Yuan and Xiaoping Ye
Titanium alloys are extensively utilized in the aerospace industry due to their exceptional properties, encompassing high specific strength and corrosion resistance. Nevertheless, these alloys present inherent challenges as difficult-to-machine materials...
ver más
|
|
|
|
|
|
|
|
|
|
|
Jaroslav Demeter, Branislav Bulko, Peter Demeter and Martina Hrubovcáková
Identification of the factors influencing refractory lining wear and its residual thickness in the basic oxygen furnace (BOF) is a prerequisite for optimizing the steelmaking process. In this study, the factors that contribute significantly to the wear o...
ver más
|
|
|
|
|
|
|
|
|
|
|
Zhimeng Li, Wen Zhong, Weiwen Liao, Yiqun Cai, Jian Zhao and Guofeng Wang
Real-time tool condition monitoring (TCM) is becoming more and more important to meet the increased requirement of reducing downtime and ensuring the machining quality of manufacturing systems. However, it is difficult to satisfy both robustness and effe...
ver más
|
|
|
|
|
|
|
|
|
|
|
Kaifeng Wang, Ziyu Lu, Yingxue Zou, Yunsheng Zhu and Junhui Yu
For improving the night recognition of road markings and enhancing the driving safety of asphalt pavements, single-factor optimization is used to investigate the effects of the component materials, including luminescent power, pigment, filler, and anti-s...
ver más
|
|
|
|
|
|
|
|
|
|
|
Zhenghong Liu and Jinxing Wu
AISI 304 has high-tensile strength and excellent corrosion resistance, which is widely needed in the energy industry and equipment manufacturing industry. However, the tools for cutting AISI 304 are easy to wear and have short service life. In order to i...
ver más
|
|
|
|
|
|
|
|
|
|
|
Sergey N. Grigoriev, Marina A. Volosova, Sergey V. Fedorov, Mars S. Migranov, Mikhail Mosyanov, Andrey Gusev and Anna A. Okunkova
The main purpose of this paper was to study the efficiency of using diamond-like carbon (DLC) coatings based on a-C:H:Si with a pre-formed CrAlSiN sublayer to increase the cutting ability of ball end mills made of KFM-39 cemented carbide at a speed of 15...
ver más
|
|
|
|
|
|
|
|
|
|
|
Dominik Piatkowski and Krzysztof Walkowiak
As the COVID-19 pandemic emerged, everyone?s attention was brought to the topic of the health and safety of the entire human population. It has been proven that wearing a face mask can help limit the spread of the virus. Despite the enormous efforts of p...
ver más
|
|
|
|
|
|
|
|
|
|
|
Leandra Bauer, Manuel Kistler, Arnd Steinbrück, Katrin Ingr, Peter E. Müller, Volkmar Jansson, Christian Schröder and Matthias Woiczinski
Wear is an important factor in the long-term success of total knee arthroplasty (TKA). Therefore, wear testing methods have become standard in implant research and development. In the EU, these are based on two simulation concepts, which are defined in s...
ver más
|
|
|
|
|
|
|
|
|
|
|
Yang Gao, Xiaoqiang Ren, Jiang Han, Fuwei Wang, Yuan Liang and Lin Liu
The microtopography of a honing wheel surface composed of active abrasive grains is the key factor affecting the honing characteristics, and control of it is a sufficient condition to realize high-efficiency precision honing. Based on the magnetron sputt...
ver más
|
|
|
|
|
|