|
|
|
|
|
Miguel Suffo, Celia Pérez-Muñoz, Gonzalo Alba and María Pilar Villar
In the wine bottling process, thermoplastics are commonly used to manufacture the crown of cork stoppers. The production of agglomerated cork stoppers generates a type of waste called cork powder (CoP) in large volumes with known properties but which are...
ver más
|
|
|
|
|
|
|
|
|
|
|
Kre?imir Nincevic, Thierry Guillet, Omar Al Mansouri and Roman Wan-Wendner
This contribution summarizes the largest available literature data collection on tensile and shear loaded anchor tests, obtained in two independent studies and performed by two different research groups. It was the objective of the two studies to investi...
ver más
|
|
|
|
|
|
|
|
|
|
|
Jakub Ka?cak, Marek Koci?ko, Adrián Vodilka, Jozef Török and Tomá? Coranic
The persistent challenge of adhesion in Fused Filament Fabrication (FFF) technology is deeply rooted in the mechanical and chemical properties of utilized materials, necessitating the exploration of potential resolutions. This involves adjustments target...
ver más
|
|
|
|
|
|
|
|
|
|
|
Edoardo Mancini, Lorenzo Mussolin, Giulia Morettini, Massimiliano Palmieri, Maria Ionica, Gianluigi Silvestre, Franck Cadoux, Agnese Staffa, Giovanni Ambrosi, Filippo Cianetti, Claudio Braccesi, Lucio Farnesini, Mirco Caprai, Gianluca Scolieri, Roberto Petrucci and Luigi Torre
Physics research is constantly pursuing more efficient silicon detectors, often trying to develop complex and optimized geometries, thus leading to non-trivial engineering challenges. Although critical for this optimization, there are few silicon tile me...
ver más
|
|
|
|
|
|
|
|
|
|
|
Ali Sadik and Filiz Karabudak
Today, especially in many fields that require structural durability, such as the aerospace and automotive industries, there has been a need to use different bonding techniques separately or together in order to use materials together with different mecha...
ver más
|
|
|
|
|
|
|
|
|
|
|
Cansu Atalay, Uzay Koc Vural, Baris Tugay, Ivana Miletic and Sevil Gurgan
The surface gloss, radiopacity and enamel/dentin shear bond strengths (SBS)s of five commercially available contemporary universal composite resins (CR)s were examined. The tested universal CRs were as follows: G-aenial A?CHORD (GA), Charisma Diamond (CD...
ver más
|
|
|
|
|
|
|
|
|
|
|
Davide Pederbelli, Luca Goglio, Davide Paolino, Massimo Rossetto and Andrea Tridello
Modern structures are designed to withstand in-service loads over a broad frequency spectrum. Nonetheless, mechanical properties in numerical codes are assumed to be frequency-independent to simplify calculations or due to a lack of experimental data, an...
ver más
|
|
|
|
|
|
|
|
|
|
|
Fantasse Azeddine, Parra Angarita Sergio, Léonard Angélique, Lakhal El Khadir, Idlimam Ali and Bougayr El Houssayne
Drinking water treatment generates a high amount of pasty by-product known as drinking water treatment sludge (DWTS). The chemical composition, microstructure and rheological behavior of DWTS are of utmost importance in the calculation, design, optimizat...
ver más
|
|
|
|
|
|
|
|
|
|
|
Emanuele Somma, Antonio Terlizzi, Maria Costantini, Madalena Madeira and Valerio Zupo
The successions of benthic communities over time are strongly influenced by the first colonizers, because surface associations are facilitated by modifications to the adhesive properties promoted by primary colonizers, such as bacteria, protozoans, diato...
ver más
|
|
|
|
|
|
|
|
|
|
|
Konstantinos Tserpes and Vasileios Tzatzadakis
For this present paper, we performed a life-cycle analysis and an evaluation of the mechanical properties of an epichlorohydrin/cardanol adhesive in a neat and a nano-filled form. Six different potentials and the cost of the adhesives were derived and co...
ver más
|
|
|
|
|
|