|
|
|
|
|
Yonglin Chen, Junming Zhang, Zefu Li, Huliang Zhang, Jiping Chen, Weidong Yang, Tao Yu, Weiping Liu and Yan Li
Lightweight fiber-reinforced composite structures have been applied in aerospace for decades. Their mechanical properties are crucial for the safety of aircraft and mainly depend on manufacturing technologies such as autoclave, resin transfer molding and...
ver más
|
|
|
|
|
|
|
|
|
|
|
Yuanping Zhou, Wenjiao Luo, Maoxing Li, Qiong Wang, Yongxin Liu and Huachun Guo
Growing potatoes (Solanum tuberosum) using the idle rice fields in Southern China and the Indo-Gangetic Plains of India in the winter season through the rice?potato rotation (RC) system could support future food security. However, the modulation capacity...
ver más
|
|
|
|
|
|
|
|
|
|
|
Ana Eusébio, Carla A. Santos and Isabel Paula Marques
Microalga Chlorella protothecoides materials were assessed as substrates for anaerobic digestion (AD) aiming at the simultaneous production of biogas/methane and pigments: whole autotrophic (AA) and heterotrophic algae (H); extracted heterotrophic microa...
ver más
|
|
|
|
|
|
|
|
|
|
|
Shangye Chu, Xu Zeng, Hai Lin and Yuting Zhu
The performance of catalytic wet oxidation of excess activated sludge derived from pharmaceutical wastewater treatment over a Cu/?-Al2O3 catalyst was investigated. The experiments were performed with a stainless steel autoclave reactor by using the prepa...
ver más
|
|
|
|
|
|
|
|
|
|
|
Rishikesh Karthikeyan, Satyanaryanan Seshadri, V Subramanya Sarma and M Kamaraj
India?s growing power demands and emission norms require more efficient coal-based power plants. The shifting of power plants from subcritical to ultra-supercritical (USC) steam conditions could improve efficiency by 12% and reduce CO2" role="presentatio...
ver más
|
|
|
|
|
|
|
|
|
|
|
Alice Proietti, Nicola Gallo, Denise Bellisario, Fabrizio Quadrini and Loredana Santo
Hybrid composite laminates are manufactured by using technologies and raw materials of the aeronautic sector with the aim to improve the damping behavior of composite structures. Matrix hybridization was achieved by laminating carbon fiber reinforced (CF...
ver más
|
|
|
|
|
|
|
|
|
|
|
Viktoriya Nelubova, Valeria Strokova, Roman Fediuk, Mugahed Amran, Nikolai Vatin and Yuriy Vasilev
In this research, a phase formation in CaO?SiO2?Al2O3?H2O binding system under hydrothermal conditions was studied. The novelty of this article lies in the quantitative full-profile X-ray diffraction (XRD) analysis used to determine kinetics of mineral f...
ver más
|
|
|
|
|
|
|
|
|
|
|
Yuan Lin and Zhidong Guan
The difference in the degree of cure of the composite in an autoclave is one of the main characterization parameters of the uniformity of the degree of cure of the composite material. Therefore, it is very important to develop an effective method for pre...
ver más
|
|
|
|
|
|
|
|
|
|
|
Wade Karlsen, Aki Toivonen and Pål Efsing
This paper describes the methods and results of analytical TEM examinations and autoclave testing of two highly-irradiated flux thimble tube materials harvested from a commercial pressurized water reactor. The materials are cold-worked 316L, and accumula...
ver más
|
|
|
|
|
|
|
|
|
|
|
Christos V. Katsiropoulos, Spiros G. Pantelakis, Marco Barile and Leonardo Lecce
?he development of a novel hybrid thermoplastic prepreg material enabling the fabrication of next-generation recyclable composite aerostructures produced by affordable, automated technologies is presented in the present work. The new hybrid material is p...
ver más
|
|
|
|
|
|