|
|
|
|
|
Beáta Ballóková, Marián Lázár, Natália Jasminská, Zuzana Molcanová, ?tefan Michalik, Tomá? Brestovic, Jozef ?ivcák and Karol Saksl
SARS-CoV-2 is the causative agent of severe acute respiratory diseases. Its main transmission pathway is through large and small respiratory droplets, as well as a direct and indirect contact. In this paper, we present the results of the development and ...
ver más
|
|
|
|
|
|
|
|
|
|
|
Behdad Garmeh, Masoud Kasiri-Asgarani, Kamran Amini, Hamid Ghayour, Hamid Reza Bakhsheshi-Rad and Filippo Berto
Carbide-free bainitic (CFB) steels with a matrix of bainitic ferrite and thin layers of retained austenite, to reduce the manufacturing costs, usually do not contain alloying elements. However, a few reports were presented regarding the effect of alloyin...
ver más
|
|
|
|
|
|
|
|
|
|
|
Bhabani Bora, Ratnesh Kumar, Somnath Chattopadhyaya and Sebastian Borucki
In this investigation, dissimilar material AA6061-T6 and Cu B370 were joined by friction stir welding (FSW). This paper presents a feasibility study of FSW to join Al-alloy and Cu-alloy. The experiment was conducted using general full factorial design by...
ver más
|
|
|
|
|
|
|
|
|
|
|
Makoto Akama and Akira Kiuchi
Rolling contact fatigue cracks in rail and wheel undergo non-proportional mixed mode I/II/III loading. Fatigue tests were performed to determine the coplanar and branch crack growth rates on these materials. Sequential and overlapping mode I and III load...
ver más
|
|
|
|
|
|
|
|
|
|
|
Yoyok Winardi,Munaji Munaji
Pág. 23 - 28
This paper presents the results of a failure analysis investigation conducted in the braking componentof motorcycle. One of the components is the brake panel. This component has been replaced in the non-authorized dealer. After used within 3 months...
ver más
|
|
|
|
|
|
|
|
|
|
|
Adrian Wei-Yee Tan, Jun Yan Lek, Wen Sun, Ayan Bhowmik, Iulian Marinescu, Xu Song, Wei Zhai, Feng Li, Zhili Dong, Chris B. Boothroyd and Erjia Liu
Cold-spraying is a relatively new low-temperature coating technology which produces coatings by the deposition of metallic micro-particles at supersonic speed onto target substrate surfaces. This technology has the potential to enhance or restore damaged...
ver más
|
|
|
|
|
|
|
|
|
|
|
Federico Nunez, Sidney Guralnick, Thomas Erber
Pág. Page 135 - 146
series of SEM micro-graphs were obtained from the cracked surfaces of samples from two types of AISI-1018 steel after applying fatigue tests at a stress ratio ofR=-1. Various strain-control levels were used in the range ±0.0008 = ? = ±0.0014 following a ...
ver más
|
|
|
|
|
|
|
|
|
|
|
Adewole, K.K.,Bull, S.J.
Pág. 87 - 95
The need to employ simulation-based investigations of fracture of civil engineering structures has been emphasised recently in literature. In this paper, three dimensional finite element simulations revealed that the cup and cone fracture process in chan...
ver más
|
|
|
|
|
|
|
|
|
|
|
F. Molleda, J. Mora, F.J. Molleda, E.J. Carrillo, E. Mora, Ma. P. Fonseca and B.G. Mellor
Pág. 102 - 106
|
|
|
|
|
|
|
|
|
|
|
Katarzyna Klyk-Spyra and Maria Sozanska
Pág. 384 - 388
|
|
|
|
|
|