|
|
|
|
|
Xianlong Peng and Yikai Wu
In order to solve the problems of low efficiency and complex cutting tools in conventional face gear machining, this paper presents a machining method of ruled surface face gears with conical cutters and proposes a new pinion to correct deviation and its...
ver más
|
|
|
|
|
|
|
|
|
|
|
Yuan-Jen Chang, He-Kai Hsu, Tzu-Hsuan Hsu, Tsung-Ti Chen and Po-Wen Hwang
With the development of next-generation airplanes, the complexity of equipment has increased rapidly, and traditional maintenance solutions have become cost-intensive and time-consuming. Therefore, the main objective of this study is to adopt predictive ...
ver más
|
|
|
|
|
|
|
|
|
|
|
Wenich Vattanapuripakorn, Sathapon Sonsupap, Khomson Khannam, Natthakrit Bamrungwong, Prachakon Kaewkhiaw, Jiradanai Sarasamkan and Bopit Bubphachot
Electricity has become one of the most important factors contributing to both the livelihoods of individuals and global economic development. Most electricity generation is still derived from burning fossil fuels that contribute to environmental degradat...
ver más
|
|
|
|
|
|
|
|
|
|
|
Tzu-Hsuan Hsu, Yuan-Jen Chang, He-Kai Hsu, Tsung-Ti Chen and Po-Wen Hwang
Landing gear is an essential part of an aircraft. However, the components of landing gear are susceptible to degradation over the life of their operation, which can result in the shimmy effect occurring during take-off and landing. In order to reduce unp...
ver más
|
|
|
|
|
|
|
|
|
|
|
Moritz Neumaier, Stefan Kranemann, Bernd Kazmeier and Stephan Rudolph
System design in an aircraft is still a costly, manual and iterative approach. One major cost driver of changes in system installation are design efforts for creating new pipes in an earlier stage and the costs accumulated during the in service life. To ...
ver más
|
|
|
|
|
|
|
|
|
|
|
Gabriel Castro and Grover Zurita
There have been steadily growing requirements from the academia and industry, demanding non-invasive methods and reliable measurement systems of research devoted to operational mode analysis (OMA). Due to the simplicity of performing only structures surf...
ver más
|
|
|
|
|
|
|
|
|
|
|
Hyo-Seong Jang, Chang-Hyun Lee, Gun-Young Park and Chul Kim
Non-circular gears can maintain rotational motions of general gears and implement all varying rotational motions of the cam. They adjust the angular velocity of driven gear according to operating conditions and make precise changes in angular motion. The...
ver más
|
|
|
|
|
|
|
|
|
|
|
Madhusudan Raghavan
Pág. 01 - 09
Engine start systems are key to providing a good customer experience for today?s drivers. Considerable effort goes into ensuring a smooth and quiet engine start, especially in vehicles equipped with start/stop systems. We present two novel mechatronic st...
ver más
|
|
|
|
|
|
|
|
|
|
|
Sangbeom Woo, Timothy Opperwall, Andrea Vacca and Manuel Rigosi
As a key component in power transfer, positive displacement machines often represent the major source of noise in hydraulic systems. Thus, investigation into the sources of noise and discovering strategies to reduce noise is a key part of improving the p...
ver más
|
|
|
|
|
|
|
|
|
|
|
Alex Rinaldi, Alberto Maria Merlo, Estefanía Hervás-Blasco, Emilio Navarro-Peris, José Miguel Coberán Salvador
Pág. 1061 - 1070
The new challenge in the reduction of CO2 emissions by heavy duty trucks is leading to a technological evolution in powertrain efficiency. Towards this objective, the EU has funded in the frame of the 7th framework program the project GASTONE: a collabor...
ver más
|
|
|
|
|
|