|
|
|
|
|
Yurianto Yurianto,Agus Suprihanto,Sumar Hadi Suryo,Yusuf Umardani,Padang Yanuar
Pág. 45 - 51
Quenched and Tempered Steel is classified as high strength and hardness steel mostly used for armor steel. Hardness and wear stability is essential for steel armor quality standards. On the other hand, austenitization and tempering temperature affect the...
ver más
|
|
|
|
|
|
|
|
|
|
|
Yurianto Yurianto,Sulardjaka Sulardjaka,Susilo Adi Widyanto,Padang Yanuar
Pág. 15 - 22
Quenched and tempered steels are needed for highly-stressed structures in military and non-military equipment. This paper was written for studying the structure and properties (hardness and impact energy absorbed) of medium-carbon and carbon-manganese st...
ver más
|
|
|
|
|
|
|
|
|
|
|
Aurel Mihail ?î?u, Andrei Victor Sandu, Alina Bianca Pop, ?tefan ?î?u, Dragos Nicolae Fra?ila, Costel Ceocea and Alexandru Boroiu
For many years, surface has quality received a serious attention due to its influence on various mechanical properties. The main contribution made in this scientific paper is the performance of actual experiments, as well as the experimental processing o...
ver más
|
|
|
|
|
|
|
|
|
|
|
Yurianto Yurianto,Pratikto Pratikto,Rudy Soenoko,Wahyono Suprapto
Pág. 55 - 61
The need for quenched and tempered steel increased, especially for the manufacture of the combat vehicle components. This steel is classified as high-strength and hardness and is bullet-resistant steel (armor steel). Maintaining the stability of steel ha...
ver más
|
|
|
|
|
|
|
|
|
|
|
Vivek Shandas, Jackson Voelkel, Joseph Williams and Jeremy Hoffman
The emergence of urban heat as a climate-induced health stressor is receiving increasing attention among researchers, practitioners, and climate educators. However, the measurement of urban heat poses several challenges with current methods leveraging ei...
ver más
|
|
|
|
|
|
|
|
|
|
|
Yurianto Yurianto,Pratikto Pratikto,Rudy Soenoko,Wahyono Suprapto
Pág. 43 - 51
Components for combat vehicles need (such as body panzers, main battle tank, armored personnel carrier) to be made of high strength and hardness steel. However, during and after the welding process is complete, this steel often leaves cracks. Quenched an...
ver más
|
|
|
|
|
|
|
|
|
|
|
Mary Beal-Hodges, Mary O. Borg, Harriet A. Stranahan
The property tax is the major source of own revenues for most city and county governments, yet economists have had very little definitive information to share with policymakers about the burden that it imposes on local citizens. This is because mos...
ver más
|
|
|
|
|
|
|
|
|
|
|
Lina Yu, Yuma Nakabayashi, Masato Sasa, Shinsuke Itoh, Masashi Kameyama, Shinro Hirano, Naoki Chigusa, Kazuyoshi Saida, Masahito Mochizuki and Kazutoshi Nishimoto
Pág. 1506 - 1515
|
|
|
|
|
|
|
|
|
|
|
I. O. Vakulenko
Pág. 202 - 206
The influence of parameters of degree of plastic deformation for 30?80 % and subsequent temper on the structure and yielding stress in the microyield region of preimproved carbon steels has been studied. The classification of dispersed phase of ferrite i...
ver más
|
|
|
|
|
|
|
|
|
|
|
Hossein ARABI, Shamseddin MIRDAMADI and A. R. ABDOLMALEKI
Pág. 1363
|
|
|
|
|
|