|
|
|
|
|
Alexander Hergt, Tobias Danninger, Joachim Klinner, Sebastian Grund, Manfred Beversdorff and Christian Werner-Spatz
In this paper, an experimental and numerical investigation of the effect of leading-edge erosion in transonic blades was performed. The measurements were carried out on a linear blade cascade in the Transonic Cascade Wind Tunnel of DLR in Cologne at two ...
ver más
|
|
|
|
|
|
|
|
|
|
|
Wenhui Yan, Zhaozheng Sun, Junwei Zhou, Kun Zhang, Jiahui Wang, Xiao Tian and Junqian Tian
One of the most commonly used techniques in aerospace engineering is the RANS (Reynolds average Navier?Stokes) approach for calculating the transonic compressor flow field, where the accuracy of the computation is significantly affected by the turbulence...
ver más
|
|
|
|
|
|
|
|
|
|
|
Haoguang Zhang, Hao Wang, Qi Li, Fengyu Jing and Wuli Chu
The aim of this research was to explore the mechanisms underlying the effect of self-circulating casing treatment with different circumferential coverage ratios on the aerodynamic performance of a transonic centrifugal compressor. A three-dimensional uns...
ver más
|
|
|
|
|
|
|
|
|
|
|
Xiaohan Xu, Xudong Huang, Dianfang Bi and Ming Zhou
Aerodynamic compressor designs require considerable prior knowledge and a deep understanding of complex flow fields. With the development of computer science, artificial intelligence (AI) has been widely applied to compressors design. Among the various A...
ver más
|
|
|
|
|
|
|
|
|
|
|
Hengtao Shi and Xianjun Yu
This paper proposes a stage flow parameter analytical model for rapid evaluation of a counter-rotating compressor?s performance for design optimization and its application in the design of a transonic counter-rotating fan. In the first part, the velocity...
ver más
|
|
|
|
|
|
|
|
|
|
|
Edwin Joseph Munoz Lopez, Alexander Hergt, Till Ockenfels, Sebastian Grund and Volker Gümmer
The successful design of compressor blades through numerical optimization relies on accurate CFD-RANS solvers that are able to capture the general performance of a given design candidate. However, this is a difficult task to achieve in transonic flow con...
ver más
|
|
|
|
|
|
|
|
|
|
|
Filippo Merli, Nicolas Krajnc, Asim Hafizovic, Marios Patinios and Emil Göttlich
The purpose of the paper is to characterize the aerodynamic behavior of a rotor-downstream hub cavity rim seal in a high-pressure turbine (HPT) stage. The experimental data are acquired in the Transonic Test Turbine Facility at the Graz University of Tec...
ver más
|
|
|
|
|
|
|
|
|
|
|
Shenren Xu, Qian Zhang, Dingxi Wang and Xiuquan Huang
Precise and inexpensive uncertainty quantification (UQ) is crucial for robust optimization of compressor blades and to control manufacturing tolerances. This study looks into the suitability of MC-adj-nonlinear, a nonlinear adjoint-based approach, to pre...
ver más
|
|
|
|
|
|
|
|
|
|
|
Yi Liu, Jiang Chen, Jinxin Cheng and Hang Xiang
The complicated flow conditions and massive design parameters bring two main difficulties to the aerodynamic optimization of axial compressors: expensive evaluations and numerous optimization variables. To address these challenges, this paper establishes...
ver más
|
|
|
|
|
|
|
|
|
|
|
Hengtao Shi
This paper researches the parametric optimization of a two-stage transonic compressor having a large air bypass at partial rotating speed according to flow analysis for a turbine-based combined cycle engine (TBCC). To obtain adequate thrust, the inlet tr...
ver más
|
|
|
|
|
|